Bayport Technical's Lockout Tagout Training System, Single Block & Bleed (150-LOTO1B), was designed to provide hands-on safety training for a wide variety of common process activities, both mechanical and electrical.
The Lucas-Nuelle CX3226-1A7 is a practical training system for teaching safe high-voltage isolation and lockout/tagout procedures for battery-electric, plug-in hybrid, and hybrid-electric vehicles.
Students learn to identify electrical hazards, choose an appropriate isolation method, verify that the vehicle is safe to service, investigate simulated faults, and recommission the vehicle after work is complete.
Designed For
- Vocational schools and community colleges
- OEM, fleet, and workforce training centers
- High school automotive programs
- Recognize electric-vehicle high-voltage hazards
- Become proficient with methods of vehicle isolation
- Investigate faults and system status
- Verify safe working conditions
- Reinitialize and recommission vehicles safely
Scan Tool Simulation
An integrated interface supports fault insertion and simulates a scan tool with diagnostic trouble codes and live data.
Multiple High-Voltage Isolation Methods
Training covers Live-Dead-Live measurements, manual service disconnects, 12-volt disconnection, cutting loops, high-voltage fuses, smart-key storage, scan-tool shutdown, and warnings for incorrect operation.
Simulated High-Voltage Circuit
The system represents an HV battery, contactor operation, high-voltage interlock loop, drive motor, DC/DC converter, and equipotential bonding circuit.
Guided Learning
Guided instruction modes and assessment activities reinforce correct procedures and decision-making.
Use of Real Workshop Tools
Students practice safety procedures using the same types of equipment used when servicing real vehicles.
Original Components
Authentic automotive components support safe, repeatable high-voltage training.
- High-voltage awareness
- High-voltage isolation methods
- Lockout/tagout procedures
- Safe-work-condition verification
- Diagnostic trouble code and fault investigation
- Safety decision-making
- Complete vehicle isolation and lockout/tagout
- Scan-tool shutdown
- Incorrect isolation procedure
- Procedure-validation failure
- Vehicle recommissioning verification
- High-voltage interlock fault investigation
- Equipotential bonding fault investigation
- Residual voltage after isolation
- Active insulation fault
- Unknown contactor status
- Collision-damaged vehicle assessment
- Authorization-limit recognition
- Unsafe-work-condition recognition
Some exercises may require separate testing equipment.
- Four-wire Kelvin milliohmmeter with a test current of at least 200 mA, resolution of 1 mOhm or better, and a pass threshold below 0.1 ohm
- Insulation and voltage tester or megohmmeter supporting 500 V and 1,000 V DC, a range of at least 200 MOhm, and a CAT III or CAT IV 1,000 V rating
Pages
-
Item Number:150-LOTO1B -
The primary goal of this course is to teach workers safe work procedures while performing work activities around electrical areas. -
Locktronics from Matrix TSL is a hands-on electrical and electronics training system that enables students to build real working circuits while learning electrical, automotive, aerospace, and installation fundamentals. -
Train EV and hybrid vehicle technicians in high-voltage isolation, LOTO procedures, electrical measurements and fault diagnosis with the Lucas-Nuelle HV Trainer. -
Item Number:295-110The model features exact, "to-scale" construction throughout. Modeled components include a liquid knockout drum, heat exchangers, choke, separators, and connecting piping, as well as representative concrete foundations and equipment supports. -
Item Number:EMT 4Train future electricians with the EMT 4 Electric Vehicle Charging Station Trainer by Lucas-Nuelle. Portable, smart, and practical — ideal for hands-on electrical vehicle equipment (EVSE) training. -
Item Number:MTECThe APT MTEC is a FANUC Certified, advanced manufacturing, CNC Load/Unload system; complete with curriculum and training for your students to integrate and program a CNC and Robot. -
Item Number:MTEC-SIMThis machine comes ready for mill and lathe operation with the robot moving a blank from a pick location to a simulated mill vice or lathe chuck all in one compact cell. The student can see the machine tool come to life on the monitor, hear the tools cutting, and crash the machine (virtually). -
Item Number:275-150DAC's Magnetic Drive Centrifugal Pump Dissectible (Goulds/IR/Durco/Flowserve) (275-150) is an industrial pump for training relating to process pumps. -
Item Number:273-910DAC Worldwide’s Magnetic Motor Starter Cutaway (273-910) depicts a professionally-crafted, sectioned example of a commonly encountered 3-phase magnetic motor starter used in industrial and commercial electrical systems to control high horsepower AC induction motors, lighting systems, and other non-inductive loads.
